Skip to content

Gnuradio flowgraphs to record multiple band segments to disk.

License

Notifications You must be signed in to change notification settings

TAPR/hpsdr_multirx

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

20 Commits
 
 
 
 
 
 
 
 
 
 

Repository files navigation

hpsdr_multirx -- 11 August 2017 -- John Ackermann N8UR -- [email protected]

The hpsdr_multirx.grc Gnuradio flowgraph allow SDR receivers that support the HPSDR "old protocol" to record semi-wideband (384ksample/second) chunks of RF spectrum. Depending on the hardware, up to seven independent receivers may be configured.

There is also a single-channel version with added capability to measure the amplitude of the strongest signal in the sampled spectrum. It's still a work in progrerss.

If there is time before the eclipse, I will upload variants preconfigured for six, three, and two channels.

These programs rely on:

  1. Gnuradio installed on a Linux computer. Development was done on a Linux Mint 18.2 system with the standard gnuradio ".deb" packages installed via apt-get, and the instructions below assume a debian-based system. Other means of installing gnuradio may put files in different locations, so might require configuration changes. It should be possible to install on a Windows system, but I haven't tested that.

NOTE: Building the digital_rf tools from MIT-Haystack requires version 3.0 or later of the "cmake" tool. Current versions of Ubuntu/Linux Mint include versions that work. However, earlier versions such as Ubuntu 14.04 or Mint 17.x have an earlier version. There are weird conflicts if you try to install the new cmake on an older system. The best bet is to use a system based on Ubuntu 16.04/Linux Mint 18 or later.

  1. The standard development environment plus tools needed for gnuradio. Install them with:

    • sudo apt-get install build-essential
    • sudo apt-get build-dep gnuradio
  2. N5EG, Tom McDermott's, gr-hpsdr blocks. Here is how to install them:

    • Create a directory in your home directory for your gnuradio files. I call mine "gr-projects" and will use that in these instructions, but use whatever name you'd like.

    • Issue these commands: cd ~/gr-projects git clone https://github.com/Tom-McDermott/gr-hpsdr cd gr-hpsdr mkdir build cd build cmake .. make sudo make install sudo ldconfig

    • cd ~/gr-projects

    • git clone https://github.com/Tom-McDermott/gr-hpsdr.git

    • cd gr-hpsdr

    • mkdir build

    • cd build

    • cmake ..

    • make

    • sudo make install

    • sudo ldconfig

  3. The MIT-Haystack "Digital RF" blocks. Here is how to install them:

    • Issue this command to install dependencies:

      sudo apt-get install libhdf5-dev python-dev python-numpy gnuradio-dev libboost-dev swig python-h5py python-tz python-dateutil python-setuptools sudo apt-get install Build: libhdf5-dev python-dev python-numpy gnuradio-dev libboost-dev swig python-h5py libhdf5 pytz python-dateutil python-setuptools

      (Some of these will probably be already installed)

    • Issue these commands:

Once these blocks have been installed, the hpsdr_multirx program should be ready to run. You can run the Gnuradio Companion (grc) program from either the start menu, or a command line, and then navigate to and open hpsdr_multirx.grc.

You'll see the flowgraph diagrammed on the grc workspace. You'll want to configure a couple of variables for your installation, and also decide on how the program operates by enabling or disabling certain of the blocks.

To enable/disable, hover the mouse on a block and right-click. You'll see a menu option to enable or disable. Click that if required. Disabled blocks are grayed-out in the workspace.

Open the "hpsdr_multirx_config.png" file that should accompany this README. It shows the flowgraph with some cribnotes on the changes you might want to make. Here are more details about those selections:

* Note that some versions of Linux assign different interface
  names to the ethernet connection.  The HermesNB block will show
  what interfaces it thinks are available, or you can issue the
  command "ifconfig" at Linux command prompt to see what's been
  assigned -- it's likely to be either "eth0" or on the newest
  OS versions something like "enXX".

* By default, the system is set up for four receivers.  You
  can increase the number by copy/pasting to create additional
  rx frequency and sink blocks, as well as adjusting the number
  of inputs for the GUI sink.

* By default, the center frequencies of the four receivers are:
	* rx0 3.675 MHz (covers ~3.487-3.862 MHz)
	* rx1 7.175 MHz (covers ~6.987-7.362 MHz)
	* rx2 10.100 MHz (covers ~9.912-10.287 MHz)
	* rx3 14.175 MHz (covers ~13.987-14.362 MHz)

* The working_dir variable should be set to the directory under
  which data files will be stored.

*  IMPORTANT: if you are using the standard Gnuradio file sink
       blocks, the working directory must exist before the flowgraph
  is run.

* The metadata variable should be edited to include your call
  (or name), the receiver type, and a description of the antenna.
  The variable is in the form of a Python "dict".  The syntax
  is as follows: {key1:val1,key2:val2,key3:val3} with any key
  or value that is a string enclosed in single quotes.  I suggest
  the following format for the solar eclipse experiment:
  {'call':'your_call','grid:'your_grid','rx':'your_rx','ant':'your_ant'}
  Use six-character grid value if possible, and if you don't have a
  ham call, use your name instead.

* The rx_samp_rate variable should be set to match the "RX Sample
  Rate" setting in the HermesNB block.

* The group of four "File Sink" blocks can be enabled (either
  individually or as a group) to record band data in the raw
  binary form that gnuradio uses by default.  For the eclipse
  experiment, disable these blocks.

* The group of four "Digital RF Channel" blocks write data to
  files in the HDF5 format.  Enable the blocks matching the
  number of receivers you are using.  USE THIS FORMAT FOR
  THE ECLIPSE TEST!

* The "QT GUI Frequency Sink" block puts a nifty spectrum display
  on the screen showing signals on each receiver.  This is really
  pretty to look at but uses quite a bit of CPU.  Use this block
  for testing, but you might want to disable it when recording
  data to ease the processor load.

* You must have one active sink block (either GUI or file/channel
  sink) for each receiver output from HermesNB.  If you're using
  less than four channels, reduce the "Num Recvs" value in the
  HermesNB block to match, disable the file blocks related to the
  disabled receivers, and reduce the number of inputs in the
  Frequency sink.  If you increase the receiver number later,
  you'll need to rewire those connections.

To stop the program (and stop recording data, close the GUI window or click the stop icon in the Gnuradio Companion window.

Using an i7-6700T @ 2.8 GHz with a solid state disk, I've had no trouble recording four 384ksample/second channels. If you see underruns ("U" characters) or other errors in the gnuradio console, first try disabling the frequency sink block. If you still have errors, you mayi need to reduce the number of receivers.

About

Gnuradio flowgraphs to record multiple band segments to disk.

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published