testing

Kconfig

@@ -1,6 +1,6 @@
 config RTL8822EU
 	tristate "Realtek 8822E USB WiFi"
 	depends on USB
-	select WIRELESS_EXT
-	help
-	  Help message of RTL8812AU
+	---help---
+	  Help message of RTL8822EU
+

Makefile

@@ -18,6 +18,9 @@ EXTRA_CFLAGS += -Wno-uninitialized
 # Let the OS decide the regd instead of phy "self-managed"
 EXTRA_CFLAGS += -DCONFIG_REGD_SRC_FROM_OS
 
+# TX NPATH config
+EXTRA_CFLAGS += -DCONFIG_RTW_TX_NPATH_EN
+
 ############ ANDROID COMMON KERNEL ############
 # clang
 ifeq ($(CC), clang)
@@ -168,7 +171,6 @@ CONFIG_SECURE_DMA_MEM_SIZE = 3686400
 ###################### Platform Related #######################
 CONFIG_PLATFORM_I386_PC = y
 CONFIG_PLATFORM_ARM_GENERIC = n
-CONFIG_PLATFORM_ARM_RPI = n
 CONFIG_PLATFORM_ARM64 = n
 CONFIG_PLATFORM_ARM64_RPI = n
 CONFIG_PLATFORM_ANDROID_X86 = n
@@ -1059,9 +1061,9 @@ ifeq ($(CONFIG_RTL8822E), y)
 RTL871X := rtl8822e
 ifeq ($(CONFIG_USB_HCI), y)
 ifeq ($(CONFIG_BT_COEXIST), n)
-MODULE_NAME = 88x2eu_ohd
+MODULE_NAME = 8812eu
 else
-MODULE_NAME = 88x2eu_ohd
+MODULE_NAME = 88x2eu
 endif
 endif
 ifeq ($(CONFIG_PCI_HCI), y)
@@ -1420,17 +1422,6 @@ INSTALL_PREFIX :=
 STAGINGMODDIR := /lib/modules/$(KVER)/kernel/drivers/staging
 endif
 
-ifeq ($(CONFIG_PLATFORM_ARM_RPI), y)
-EXTRA_CFLAGS += -DCONFIG_LITTLE_ENDIAN
-EXTRA_CFLAGS += -DCONFIG_IOCTL_CFG80211 -DRTW_USE_CFG80211_STA_EVENT
-ARCH ?= arm
-CROSS_COMPILE ?=
-KVER ?= $(shell uname -r)
-KSRC := /lib/modules/$(KVER)/build
-MODDESTDIR := /lib/modules/$(KVER)/kernel/drivers/net/wireless/
-INSTALL_PREFIX :=
-endif
-
 ifeq ($(CONFIG_PLATFORM_ARM_GENERIC), y)
 EXTRA_CFLAGS += -DCONFIG_LITTLE_ENDIAN -DCONFIG_IOCTL_CFG80211 -DRTW_USE_CFG80211_STA_EVENT
 ARCH ?= arm

README.md

@@ -1,24 +1,14 @@
 # rtl88x2eu-20230815
-Linux Driver for WiFi Adapters that are based on the RTL8812EU and RTL8822EU Chipsets - v5.15.0.1  
-``` rtl88x2EU_rtl88x2CU-VE_WiFi_linux_v5.15.0.1-186-g768722062.20230815_COEX20230616-330a-beta.tar.gz ```  
+Linux Driver for WiFi Adapters that are based on the RTL8812EU and RTL8822EU Chipsets, based on driver ```v5.15.0.1-197```
 
-This branch is mainly focused on FPV. Checkout [commit 690d429](https://github.com/libc0607/rtl88x2eu-20230815/commit/690d429ec272892d5388d744097e3c3cb15dad1b) for the original driver from Realtek, or [commit 5c9355d](https://github.com/libc0607/rtl88x2eu-20230815/commit/5c9355df330a8745a63c06acf1a10203c1d6f804) with build fixes on kernel 6.5.  
-
-I've asked LB-LINK (a Wi-Fi module vendor) for any RTL8812EU driver. Then he sends me this tar.   
-So, it should work with RTL8812EU and RTL8822EU.   
-
-According to the file name, it may work with RTL8812CU or RTL8822CU (if exists). But you should use an in-kernel driver instead.
-
-My personal to-do list: 
-- Figure out how to make the packet injection work correctly (idk if I'm doing it correctly -- needs help) -- generally, it works! but it's not been fully tested and idk how many bugs it has (
-- Test with any OpenIPC camera -- It was reported working on SSC338Q/SSC30KQ and Hi3516/GK7205 (with CONFIG_WIRELESS_EXT enabled)
-- Figure out how to transmit in 5M/10M bandwidth (The feature is claimed to be supported in the module's product page. see [CONFIG_NARROWBAND_SUPPORTING](https://github.com/search?q=repo%3Alibc0607%2Frtl88x2eu-20230815+CONFIG_NARROWBAND_SUPPORTING&type=code) and [hal8822e_fw_10M.c](https://github.com/libc0607/rtl88x2eu-20230815/blob/v5.15.0.1/hal/rtl8822e/hal8822e_fw_10M.c)) -- Only 10MHz bandwidth works well in injection mode
-- Build with dkms
-- Test on more architecture, kernels, and distributions
-- An open-source hardware design using the LB-LINK module, then share it somewhere else -- done, see [here](https://oshwhub.com/libc0607/bl-m8812eu2-demoboard-v1p0)  
+This branch is mainly focused on FPV. Checkout [commit 690d429](https://github.com/libc0607/rtl88x2eu-20230815/commit/690d429ec272892d5388d744097e3c3cb15dad1b) for the original driver from Realtek.  
 
 PRs welcome.
 
+## Hardware 
+BL-M8812EU2 datasheet: [BL-M8812EU2_datasheet_V1.0.1.1_240511.pdf](https://github.com/user-attachments/files/16627775/BL-M8812EU2_datasheet_V1.0.1.1_240511.pdf)  
+Or any adaptor based on RTL8812EU/RTL8822EU should be ok.  
+
 ## Increasing TX Power in Monitor Mode 
 The driver supports changing TX power dynamically with no additional patch needed.  
 Just add ```rtw_tx_pwr_by_rate=0 rtw_tx_pwr_lmt_enable=0``` when ```insmod```, then use ```iw set txpower fixed```.
@@ -27,6 +17,7 @@ The relative TX gain under different settings was measured by my HackRF with the
 The results do tell the difference. However, I don't have a spectrum analyzer, so I don't know the absolute TX power value.   
 
 Be careful when you try these cmds as the adaptor can be VERY HOT. Use a good heat sink and install the antennas properly.  
+Make sure the antenna is connected before transmitting, or you can damage your adaptor's PA. The BL-M8812EU2 has nothing like "antenna lost protection".  
 
 Example: 
 ```
@@ -42,33 +33,48 @@ sudo insmod 8812eu.ko rtw_tx_pwr_by_rate=0 rtw_tx_pwr_lmt_enable=0
 # but when mbm is higher than ~2000 (may different), the PA starts to saturate and the increase becomes smaller
 sudo iw dev wlan0 set txpower fixed <mBm>
 ```
-Tested on my Ubuntu 22.04 VM, kernel 6.5.   
 
-Note: Changing TX power by ```iw``` will not work when injecting with 10MHz BW (see below).  
-You should manually set BW back to 20MHz, set TX power, then set BW back again.  
-
-## 10MHz Bandwidth Transmission
+## Narrowband Transmission
 See the RF spectrum visualized [here](https://www.youtube.com/watch?v=EUj-wSgoY_E) on YouTube  
 
 There's a lot to explore in this crab driver and will update here if something new has been discovered.  
 Please open an issue if you find anything interesting.  
 
 So, according to the module vendor's document and my test using a HackRF, that's all I know:   
 
-### Injection
-To transmit packets in monitor mode using packet injection, set ```iw <wlan> set channel <same_channel> 10MHz``` on both air & ground.  
-Then when transmitting in 20MHz bandwidth (e.g. bandwidth=20 in wfb_ng), the packet is actually transmitted in 10MHz bandwidth, which seems like being achieved by simply underclocking the baseband.  
-It's the same on the receiver side, though in which the radiotap header in received packets still indicates a 20MHz bandwidth. 
-
-But when ```iw``` says ```Devices or Resources Busy (-16)```, check ```iw <wlan> info``` if the ```iw``` recognized the adaptor is in monitor mode.   
-If not, ```iw <wlan> set monitor```, then try setting 10MHz again.  
-
+### Injection in Different Bandwidth
+#### 5/10MHz Injection
+To transmit packets in monitor mode using packet injection:
+ - Set ```iw <wlan> set channel <same_channel> <10MHz>``` on both air & ground
+ - Set the inject packet's radiotap header with any **20MHz bandwidth** modulation (legacy/HT20/VHT20; e.g. ```-B 20``` in ```wfb_tx```) 
+Then the packet is actually transmitted in 5MHz/10MHz bandwidth, which seems like being achieved by simply underclocking the baseband.  
+It's the same on the receiver side, though in which the radiotap header in received packets still indicates a 20MHz bandwidth. You can check that with any SDR receiver or spectrum analyzer.   
+
+##### Notes About "Devices or Resources Busy" 
+When ```iw``` says ```Devices or Resources Busy (-16)```, check ```iw <wlan> info``` if the ```iw``` recognized the adaptor is in monitor mode.   
+If not, ```iw <wlan> set monitor```, then try setting 5MHz/10MHz again.  
 That's because:  
 1. The crab driver supports both WEXT and cfg80211 APIs, but it seems that it's not that robust and there's some conflicts exist
 2. the cfg80211 API checks [here](https://github.com/OpenIPC/linux/blob/eb50a943c26845925ff11ccb1651c40fa02c105e/net/wireless/chan.c#L862) if there's any other interface is not in monitor mode
 3. If the monitor mode is set by ```iwconfig```, the process is done by calling the old WEXT APIs, so the cfg80211-based ```iw``` may not get the latest status and think the interface is still in managed mode
 
-### AP/STA
+##### Notes About 5MHz 
+EXPERIMENTAL 5MHz support is not in the main branch, I've put that in [another branch here](https://github.com/libc0607/rtl88x2eu-20230815/tree/5mhz_bw).   
+It works by fixing the config in the DAC clock setting register (See [this commit](https://github.com/libc0607/rtl88x2eu-20230815/commit/67dbbff1f01b8edd5b532c2a2c6e719452740ff5)), but it still needs testing as there are no register-level documents available and no one knows if those changes will affect the 20/40/80MHz transmission.  
+
+The register value is from the RTL8812CU driver, which works well in 5MHz BW. The RTL88x2Cx and RTL88x2Ex share the same internal codename "Jaguar3" so I've just assumed that they have some common register defines, and it works.   
+Tested between RTL8812EU and RTL8812CU ([driver](https://github.com/libc0607/rtl88x2cu-20230728)), both TX and RX.  
+
+**Update**:  Some leakage (mirror?) can be observed in the 5MHz mode, and I have no idea how to configure the DAC clock properly as there are no even definitions in .h files. So, 5MHz is not recommended. However, I'll keep that branch for further research. 
+
+##### Note about Changing TX Power in Narrowband Modes
+Changing TX power by ```iw``` will not work when injecting with 5/10MHz BW.  
+You should manually set BW back to 20MHz, set TX power, then set BW back again.  
+
+#### 20/40/80MHz Injection
+Use ```iw``` to set channel & NOHT/HT20/HT40/80MHz bandwidth, then set the correct bandwidth in the radiotap header (can be done by using ```-B``` in wfb-ng)   
+
+### 10MHz BW AP/STA 
 It's currently under testing by a Chinese enthusiast, will update here if he has any progress.  
 According to the module vendor's ambiguous document and the crab's mysterious driver tar with a "_10MHz" suffix:  
 1. Enable ```CONFIG_NARROWBAND_SUPPORTING``` in ```include/hal_ic_cfg.h``` (in ```#ifdef CONFIG_RTL8822E``` section if using RTL8812EU), then ```#define CONFIG_NB_VALUE RTW_NB_CONFIG_WIDTH_10``` below
@@ -77,14 +83,7 @@ According to the module vendor's ambiguous document and the crab's mysterious dr
 4. ```iw``` Set the channel to 10MHz bandwidth
 5. If there are any tools complain about the Wi-Fi regularities when setting up a 10MHz AP,  try setting the channel plan manually by ```echo 0x3E > /proc/net/rtl88x2eu/<wlan>/chan_plan```.
 6. Check the ACK timeout setting below if the range is >\~3km
-7. Check ```/proc/net/rtl88x2eu/<wlan>/rate_ctl``` for manually control of the rate
-
-### Is Injecting in Other Bandwidth Available?
-#### 5MHz
-No. It performs like a fractional RF synthesizer with only a single tone appearing on my SDR receiver.
-#### 40MHz/80MHz
-It works.   
-Use ```iw``` to set channel & HT40/80MHz bandwidth, then set 40MHz or 80MHz(VHT) in radiotap header (can be done by using ```-B``` in wfb-ng)   
+7. Check ```/proc/net/rtl88x2eu/<wlan>/rate_ctl``` for manually control of the rate if needed. See [@Vito-Swift's tutorial here](https://github.com/Vito-Swift/rtl8814au-ext/blob/main/doc/how_to_do_unicast_rc.md)  
 
 ## Set (Unlocked) Channel in procfs  
 The chip's RF synthesizer can work in a bit wider range than regular 5GHz Wi-Fi.  
@@ -100,9 +99,11 @@ Some chips' synthesizer's PLL may not lock on some frequency. There's no guarant
 Unlocking the frequency may damage your hardware and I'm not gonna pay for it. Use it at your own risk.  
 Please comply with any wireless regulations in your area.  
 
-## Override default EDCCA Threshold  
+## EDCCA
 WARNING: YOU SHOULD NOT USE THIS (unless someone's DJIs next to you f***ed up all channels XD). It's not fair.  
+DISCLAIMER: There's no guarantee of its performance. This may damage your hardware and I'm not gonna pay for it. Use it at your own risk. Please comply with any wireless regulations in your area.  
 
+### Override default EDCCA Threshold  
 To override dafault EDCCA threshold, check ```cat /proc/net/rtl88x2eu/<wlan0>/edcca_threshold_jaguar3_override```.  
 
 e.g. ```ech0 "1 -3O" > /pr0c/net/rt188x2eu/<w1anO>/edcca_threshO1d_jaguar3_Override```   
@@ -112,7 +113,9 @@ If there are any, the adaptor will wait until the energy level in the air is low
 Note that there are actually two values, L2H and H2L. The L2H is typically set 8dB higher so it creates a hysteresis.   
 The value you're setting is L2H. The H2L is automatically set 8dB lower.  
 
-DISCLAIMER: There's no guarantee of its performance. This may damage your hardware and I'm not gonna pay for it. Use it at your own risk. Please comply with any wireless regulations in your area.  
+### Disable CCA (EXPERIMENTAL)
+```echo "1" > /proc/net/rtl8812eu/<wlan0>/dis_cca```  
+Needs test.  
 
 ## ACK Timeout 
 Provided by Realtek.
@@ -148,7 +151,60 @@ However, it can be used to estimate the status of the chip, "cool/warm/hot/smoke
 See [PR #4](https://github.com/libc0607/rtl88x2eu-20230815/pull/4) and [commit/5b7a66d](https://github.com/libc0607/rtl88x2eu-20230815/commit/5b7a66d3b1c7097a02247f91253993a7027e40a6#comments) for more details.  
 The offset can be tuned by ```echo "<offset>" > /proc/net/rtl88x2eu/<wlan0>/thermal_state```. By default, it's ```32```, based on my measurement.  
 
-## Use with OpenIPC  
-See the tutorial [here in OpenIPC Wiki](https://github.com/OpenIPC/wiki/blob/master/en/fpv-bl-m8812eu2-wifi-adaptors.md).  
-Or, download pre-built firmware with this driver from [here](https://github.com/libc0607/openipc-firmware).
+## TX NPATH setting  
+Realtek didn't say anything about the feature, but IMO it should be the Cyclic Shift Diversity (CSD) feature ([A 'sine wave' can be seen on top of the OFDM spectrum](https://www.youtube.com/watch?v=IGf5MKOmX6k) when enabled).  
+Only works when 1. injecting legacy rates, or 2. injecting in MCS rates with only 1 spatial stream enabled and STBC disabled.  
+Use ```rtw_tx_npath_enable=1``` when ```insmod``` to enable the feature. You can see a significant input current difference.  
+Like the STBC, it's another transmit diversity technique. Need more tests to tell the difference in the FPV scenario.  
+
+## Generating Single Tone  
+To generate a single tone at the carrier frequency, 
+ 1. Set monitor mode & any channel, e.g. ```iwconfig wlan0 mode monitor channel 52``` (5260 MHz)
+ 2. ```echo "1 4" > /proc/net/rtl88x2eu/<wlan0>/single_tone```, in which ```<EN:0/1>```, ```<RF_PATH:0(A)/1(B)/4(AB)>```
+ 3. Remember to set ```EN``` back to ```0``` before any normal operation
+
+Useful when generating any signal without PAPR matters.  
+![image](https://github.com/user-attachments/assets/e664bbf1-d2d1-4648-b28a-ec3d1c199009)  
+
+### Generating the 5.340 GHz Single Tone 
+For TinySA Ultra "Calibration above 5.34 GHz". See the [guide here: tinySA Ultra harmonic mode](https://tinysa.org/wiki/pmwiki.php?n=TinySA4.Harmonic).   
 
+DISCLAIMER: **ALWAYS CONNECT THE ATTENUATOR**, or you could accidentally damage the SA's input.  
+The output performance is limited by the cheap crystal inside the blue square.  
+**Use it at your own risk.**  
+```
+# 1. Set the adapter to monitor mode (see nic_quick_test.sh)
+# Any 5 GHz channel is ok for the script argument
+sudo ./nic_quick_test.sh <wlan0> 60
+
+# 2. Set the center frequency to 5.340 GHz (Channel 68)
+# The frequency is usually disabled due to wireless regulation, so use /proc
+echo "68 20" > /proc/net/rtl88x2eu/<wlan0>/monitor_chan_override   # freq = 5000+68*5 = 5340 MHz
+
+# 3. Generate single tone
+# The blue square has two IPEX connector J0 and J1 (see BL-M8812EU2 datasheet)
+echo "1 0" > /proc/net/rtl88x2eu/<wlan0>/single_tone               # Output at J0 only
+# echo "1 1" > /proc/net/rtl88x2eu/<wlan0>/single_tone              # Output at J1 only
+# echo "1 4" > /proc/net/rtl88x2eu/<wlan0>/single_tone              # Output at both J0 and J1
+
+# 4. Change to some other frequency (e.g. manually tuning by ```leveloffset harmonic```)
+echo "0 0" > /proc/net/rtl88x2eu/<wlan0>/single_tone               # !! ALWAYS DISABLE THE OUTPUT FIRST !!
+echo "69 20" > /proc/net/rtl88x2eu/<wlan0>/monitor_chan_override   # 5345 MHz
+echo "1 0" > /proc/net/rtl88x2eu/<wlan0>/single_tone               # Output at J0 only
+# ... do some calibration stuff
+echo "0 0" > /proc/net/rtl88x2eu/<wlan0>/single_tone               # !! ALWAYS DISABLE THE OUTPUT FIRST !!
+echo "67 20" > /proc/net/rtl88x2eu/<wlan0>/monitor_chan_override   # 5335 MHz
+echo "1 0" > /proc/net/rtl88x2eu/<wlan0>/single_tone               # Output at J0 only
+# ... do some calibration stuff
+
+# 5. disable the output
+echo "0 0" > /proc/net/rtl88x2eu/<wlan0>/single_tone               # !! DISABLE THE OUTPUT !!
+
+```
+![image](https://github.com/user-attachments/assets/0a17dd57-1cee-49aa-9d05-45c0e25097cc)
+
+
+## Use with OpenIPC  
+The driver has been integrated into the default FPV firmware for SSC30KQ, SSC338Q, and SSC377DE since [this commit](https://github.com/OpenIPC/firmware/commit/64228b686002b2fd8fd2cbf722a1a6cb7aad9650).  
+For other platforms, see the tutorial [here in OpenIPC Wiki](https://github.com/OpenIPC/wiki/blob/master/en/fpv-bl-m8812eu2-wifi-adaptors.md).  
+Or, download pre-built firmware with this driver from [here](https://github.com/libc0607/openipc-firmware).  

dkms-install.sh

@@ -7,8 +7,8 @@ else
   echo "About to run dkms install steps..."
 fi
 
-DRV_DIR=rtl88x2eu_ohd
-DRV_NAME=rtl88x2eu_ohd
+DRV_DIR=rtl88x2eu
+DRV_NAME=rtl88x2eu
 DRV_VERSION=5.15.0.1
 
 cp -r $(pwd) /usr/src/${DRV_NAME}-${DRV_VERSION}

dkms-remove.sh

@@ -7,8 +7,8 @@ else
   echo "About to run dkms removal steps..."
 fi
 
-DRV_DIR=rtl88x2eu_ohd
-DRV_NAME=rtl88x2eu_ohd
+DRV_DIR=rtl88x2eu
+DRV_NAME=rtl88x2eu
 DRV_VERSION=5.15.0.1
 
 dkms remove ${DRV_NAME}/${DRV_VERSION} --all

dkms.conf

@@ -1,7 +1,7 @@
-PACKAGE_NAME="rtl88x2eu_ohd"
-PACKAGE_VERSION="5.15.0.1~20230815_ohd"
+PACKAGE_NAME="realtek-rtl88x2eu"
+PACKAGE_VERSION="5.15.0.1~20230815"
 CLEAN="'make' clean"
-BUILT_MODULE_NAME[0]=rtl88x2eu_ohd
+BUILT_MODULE_NAME[0]=8812eu
 PROCS_NUM=`nproc`
 [ $PROCS_NUM -gt 16 ] && PROCS_NUM=16
 DEST_MODULE_LOCATION[0]="/updates"

include/autoconf.h

@@ -19,8 +19,8 @@
  * Public  General Config
  */
 #define AUTOCONF_INCLUDED
-#define RTL871X_MODULE_NAME "rtl88x2eu_ohd"
-#define DRV_NAME "rtl88x2eu_ohd"
+#define RTL871X_MODULE_NAME "88x2EU"
+#define DRV_NAME "rtl88x2eu"
 
 /* Set CONFIG_RTL8822E from Makefile */
 #ifndef CONFIG_RTL8822E

include/drv_types.h

@@ -2230,8 +2230,4 @@ int rtw_suspend_free_assoc_resource(_adapter *padapter);
 	#include <pci_hal.h>
 #endif
 
-// OpenHD crda workaround
-int get_openhd_override_channel(void);
-int get_openhd_override_tx_power_mbm(void);
-
 #endif /* __DRV_TYPES_H__ */

nic_quick_test.sh

@@ -4,10 +4,9 @@ NIC=$1
 CHANNEL=$2
 
 echo "insmod"
-rmmod 88x2eu_ohd
-else
+rmmod 8812eu
 modprobe cfg80211
-insmod 88x2eu_ohd.ko rtw_regd_src=1 rtw_tx_pwr_by_rate=0 rtw_tx_pwr_lmt_enable=0 
+insmod 8812eu.ko rtw_regd_src=1 rtw_tx_pwr_by_rate=0 rtw_tx_pwr_lmt_enable=0 
 
 echo "set $NIC monitor mode"
 airmon-ng check kill