Trackplan

Signal

Station	track	Sinal	Placment	SW	Address	CV High	CV Low	Default	Decoder
Main	1	sgMsp1s-	Main	1	420	1	164	Red	Buildin
				2	421	1	165
	2	sgMsp2s+	Main	1	422	1	166	Red	Buildin
				2	423	1	167
	3	sgHsp3-	Main	1	424	1	168	Red	Buildin
				2	425	1	169
	3	sgHsp3+	Main	1	426	1	170	Red	Buildin
				2	427	1	171

Station	track	Sinal	Placment	SW	Address	CV High	CV Low	Default	Decoder
Lake	1	sgLsp1s-	Lake	1	405	1	149	Green	Buildin
	2	sgLsp2s+	Lake	1	406	1	150	Red	Buildin
				2	407	1	151

Station	track	Sinal	Placment	SW	Address	CV High	CV Low	Default	Decoder
Driveway	1	sgIsp1+	Small house	1:1	450	1	194	Red	LSD
				1:2	451	1	195	Red	LSD
	3	sgIsp3-	Small house	2:1	452	1	196	Red	LSD
				2:2	453	1	197	Red	LSD
	1	sgIsp1-	Well	1:1	454	1	198	Red	LSD
				1:2	455	1	199	Red	LSD
	3	sgIsp3+	Well	2:1	456	1	200	Red	LSD
				2:2	457	1	201	Red	LSD

From	To	Sinal	Placment	SW	Address	CV High	CV Low	Default	Decoder
Ter.sw	Lake	sg8-	Lake	1	401	1	145	Green	Buildin
				2	402	1	146
Lake	Ter.sw	sg8+	Ter.sw	1	403	1	147	Red	Buildin
				2	404	1	148
Main North	Lake In	sgSpHInw+	Lake	1	458	1	202	Red	Buildin
				2	459	1	203
Lake In	Main North	sgSpHInw+	Lake	1	460	1	204	Red	Buildin
				2	461	1	205
Main Norh	Driveway	sgIspHn-	Lake	1	462	1	206	Red	Buildin
				2	463	1	207

Programming

Buildin MD SH-12

• Address SW1 High CV120 value from table
• Address SW1 Low CV121 value from table
• Address SW2 High CV125 value from table
• Address SW2 Low CV126 value from table
• Signal type CV49 value 38

2 in 1 MD LSD

• Signal type CV14 Mode 2 3 light signal CV value 2
• Address Signal 1 SW 1 High CV20
• Address Signal 1 SW 1 Low C21
• Address Signal 1 SW 2 High CV22
• Address Signal 1 SW 2 Low C23
• Address Signal 2 SW 1 High CV24
• Address Signal 2 SW 1 Low C25
• Address Signal 2 SW 2 High CV26
• Address Signal 2 SW 2 Low C27

Rocrail

Signal 3 aspects

Interface tab

Detail tab

Sensors

MD

Overview of the RBM setup

The source to the picture https://app.diagrams.net/#HMaxWinther%2Frocrail%2Fmain%2Frbm-setup.drawio

MD BM programming

• CV30 Current detection L1, default 5
• CV31 Current detection L2, default 5
• CV32 Current detection L3, default 5
• CV33 Current detection L4, default 5

Rocrail Setup Sensors are mapped to mXion in the interface tab setting the follwing

• Interface ID to md
• Node ID aka Bus for Z21 protocol to 1 which actually stands for responses comming from LocoNet
• Address is set to the programmed address in RBM plus 1

Massoth

Overview of RM setup

The source to the picture https://app.diagrams.net/#HMaxWinther%2Frocrail%2Fmain%2Fmassoth_feedback_layout.drawio

How to integrate MD BM and Massoth RM

The source to the picture https://app.diagrams.net/#HMaxWinther%2Frocrail%2Fmain%2FMD_BM_to_Massoth_RM_8170001.drawio

Remember to program CV 65, 75 and 85 same as CV 55

Usage

From tables below in phase 1, isolators 31 and 21

• Main station 6 and 4
• Lake station 6 and 4
• Driweway station 6 and 4
• Main line 13 and 9

From tables below in phase 2, isolators 20 and 14

• Main station 16 and 11
• Main line 4 and 3

Feedback modules

1. Main station; block track 1 and track 2. Main line block to Terrase switch, and one sensor in block Lake to Terrase switch. One free sensor
2. Lake station; block track 1 and track 2. Main Line switch to Lake, and two sensors in block Lake to Terrase switch. No free sensors.
3. Driveway; blocks and sideways on station plus single main line block. No free sensors

Station	Track	Block	Isolartor	Sensor	Phase	FB
Main	1		3	2	1	HS1:1 HS1:2
	2		3	2	1
	3		4	3	2
	4N		3	2	2
	4S		3	2	2
	5N		3	2	2
	5N		3	2	2
Total			6	4	1
			16	11	2

Station	Track	Block	Isolartor	Sensor	Phase	FB
Lake	1		3	2	1	LS1:1:324 LS1:2
	2		3	2	1
Total			6	4	1

Station	Track	Block	Isolartor	Sensor	Phase	FB
Driveway	1		3	2	1	DW1:1 DW1:2
	2		1	1	3
	3		3	2	1	DW2:1 DW2:2
	4		1	1	3
Total			6	4	1

From	To	Block	Isolartor	Sensor	Phase	FB
Main	Ter.sw	bkHspHe	3	2	1	HS1:3 HS1:4
Ter.sw	Lake	bkspHLn	4	3	1	LS1:3:324 LS1:4
Driveway	Switch	bkIspHn	3	2	1	DW1:3 DW1:4
Switch	Lake	bkspHInw	3	2	1
Main	Ter.sw	bkHspHs	4	3	2
Total			13	9	1

rocrail.ini

Set up mXion

The property

• xnetgbm enables feedback via Loconet
• host ip-address of CS mXion; Upladsgade 10.76.215.157, Sommerhus 192.168.8.197
• libpath actual path to drivers in the rocrail install

MacOS

<digint lib="z21" iid="md" port="21105" uid="0" 
    host="10.76.215.157" locolist="false" absent="false" xnetgbm="true" swtime="250" protver="0" desc="mXion" 
    ignorepowercmds="true" 
    ignorepoweroffonghost="false" 
    show="true" swapgates="false" stress="false" guid="0000ACDE480020210303160626126000" 
    libpath="/Applications/Rocrail.app/Contents/MacOS"/>

Set up webclient

<webclient 
    port="8081" 
    webpath="web" 
    imgpath="images" 
    svgpath1=svg/themes/SpDrS60" 
    svgpath2="." 
    svgpath3="." 
    svgpath4="." 
    svgpath5=".">
    <rocweb/>
</webclient>

Raspberry PI

Install new server version

• Follow download instructions from https://wiki.rocrail.net/doku.php?id=download-int#raspberry_pi
• Download to /home/pi/Downloads
• Unzip into sudo unzip -u Rocrail-PiOS11-ARMHF.zip -d /opt/rocrail-[VERSION]-[DDMMYYY]
• Remove old symbol-link sudo rm /opt/rocrail
• Create net symbol-link sudo ln -s rocrail-[DD-MM-YYY] rocrail in opt-folder
• Create symbol-link in new folder to rocrai-bin like sudo ln -s bin/rocrail rocrail to make init.d work

Setup

Installed and runing from aka working-directory

/home/pi/rocrail/testPlan

Symbolic links in working directory, only done once

• web ln -s /opt/rocrail/web web
• svg ln -s /opt/rocrai/svg svg

Start/stop

• Stop: sudo /etc/init.d/rocraild stop
• Start: sudo /etc/init.d/rocraild start
• Status: /etc/init.d/rocraild status

MacOS

Setup

Symbolic links created by installation