Skip to content

Latest commit

 

History

History
158 lines (112 loc) · 5.75 KB

TODO

File metadata and controls

158 lines (112 loc) · 5.75 KB

TODO List -*-org-*-

THIS LIST IS FAR AWAY FROM BEING COMPLETE, so these are the few things that came up at the right moment to be written down.

Random issues:

Run the code checker sparse harder on the code: CC=cgcc make

Start work on ironing out a TODO list for RFC 4601 compliancy.

Look into updates RFC 5059 and RFC 5796

Test again on Debian GNU/kFreeBSD. Atm it lacks netinet/pim.h, but

it should be possible to run the default config on it, probing the __FreeBSD_kernel__ and doing the right thing.

Check Kame’s pim6sd old sources for relevant fixes.

http://www.kame.net/dev/cvsweb2.cgi/kame/kame/kame/pim6sd/Attic/

Import Kame’s pim6sd cfparse.[yl] config file parser reimplemented

in lex & yacc, like mrouted does.

When receive PIM_REGISTER, check whether I am the chosen RP

Install negative cache in kernel for non-frequently requested groups.

The code should use the _PIM_VT handling of the ‘struct pim’

Check 2.10 from the spec “Unicast Routing Changes”, and verify

that it is properly implemented

<masklen> in pimd.conf should be mandatory, instead of relaying

of its default value (16)

Candidate RP priority configuration in pimd.conf should be per

prefix, instead of a single priority for the whole RP.

Check whether Asserts received on the iif are really evaluated

by using the metrics of other asserts received on that iif, or the comparison uses the local metric and preference info (it must be the former!).

Experimental kernel MFC (*,G) related:

If the (S,G) iif or oifs are different from the (,G) or (,*,RP) iifs/oifs, the resp. (,G) or (,*,RP) will delete and disallow creating (,G) MFC. Only after all MRT (S,G) are deleted, the corresponding (,G) or (,,RP) will create (*,G) MFC.

Experimental kernel MFC (*,G) related:

Right now when the MFC (,G) total datarate is above the SPT switch threshold, the (,G) MFC will be deleted, and any further cache miss will result in (S,G) MFC (the problem is that we must do (S,G) monitoring for eventually high datagate sources). Only after all (S,G) MFCs expire, the daemon’s MRT will stop creating (S,G) MFCs (i.e. the next cache miss will result in (*,G) kernel MFC). A better selection should be applied to sort out the higher datarate sources, and at the same time to have (,G)MFC as well. For example, create few (S,G), and after that create the (,G). If some of the created (S,G) MFC entries have very low datarate, delete them.

Use NetBSD’s definition for IPADDR (netinet/in.h):

#ifdef _KERNEL #define __IPADDR(x) ((u_int32_t) htonl((u_int32_t)(x))) #else #define __IPADDR(x) ((u_int32_t)(x)) #endif

The (S,G)RPbit in the DR for the sender and the (S,G)SPT in the

downstream router won’t timeout and will refresh each other even if the sender is not active:

S–DR-----------------R1------------RP (S,G)RPbit (S,G) iif toward S

Check whether the kernel code sends CACHE_MISS and WRONG_IIF for

the LAN-scoped addresses

If the RP for a group changes, the DR should cancel any PIM-register-stop

timers (XXX: not in the spec, but should be there)

If a new interface is configured, include it automatically

Don’t create routing entries for local link scoped groups

Implement adm. scoped filters

Do precise check of the timer events to speed up the propagation of the

Cand-RP messages + Cand-BSR messages and the election of the BSR.

Fix the bug for messing up the things when the receiver is on the

same host as the RP for the multicast group (probably was fixed with alpha6, because I cannot reproduce it anymore)

Do more precise error check for the received PIM messages. In most cases,

the whole message must be parsed completely before starting processing it.

Clean up the debugging messages.

Use Patricia tree to search the routing table

(There is a nice paper in Sigcomm ‘97 about fast routing tables implementation, so need to check it as well)

Do switch back to the Shared Tree by timing out the SPT if the rate

is too low (not in the spec, but Ahmed pointed out some complications if this happens)

Change all countdown timers to events timeout (callout.c)

(The current implementation is very unefficient if the routing table becomes very large)

Send immediately Join/Prune, instead of relying of Join/Prune timer = 0

Fix the code allowing interface UP/DOWN without restarting pimd.

Do more testings for SPT switch, Join/Prune, asserts, etc…

Test the (,,RP) code (need PIM/DVMRP border router to do so)

Test the RSRR (RSVP support) code

Send Initial_Reply RSRR message if the interfaces detected by pimd change

SNMP support, RFC2934

Issues by function name:

igmp_proto.c:

  • accept_group_report():
    • add a leaf if DR or forwarder (currently only if DR)???
  • accept_leave_message():
    • send immediately PIM prune message if the last member has left

main.c

  • main():
    • use a combination of time and hostid to initialize the random generator.
  • restart():
    • check the implementation

pim_proto.c

  • pim_register():
    • IF THE BORDER BIT IS SET, THEN FORWARD THE WHOLE PACKET FROM USER SPACE AND AT THE SAME TIME IGNORE ANY CACHE_MISS SIGNALS FROM THE KERNEL.
  • register_stop():
    • REGISTER_STOP rate limiting

route.c

  • process_cache_miss()
    • use negative cache.

rp.c

  • add_rp_grp_entry():
    • FIX THE BUG when adding an RP for different prefix requires remapping for some groups!!! (Intentionally left, waiting to come up with an idea how to implement it simple and efficient. If you configure all RPs to advertise the same prefix, the bug won’t “show up”)